Vroom vroom

New Project : Air Intake Swap

New Project : Coming Soon

"fuyo.."

5th Mod : Takeda Stage 2 Pro Dry S (Black)

Takeda Stage 2 Pro Dry S box

Fully imported from US

Parts that makes up a Takeda

Removing standard airfilter box

Removed original airfilter box

New air intake : Takeda Stage 2 Pro

"Fuyo.."

4th Mod : Eibach Lowering Spring

Eibach Lowering Spring Japan Spec

Contents of what inside

Left : Original Rear Spring. Right : Eibach Lowering Spring (Rear)

Top : Original Front Spring 

Bottom : Eibach Lowering Spring (Front)

View of the original spring placement

View of the newly installed Eibach

View before Eibach

View with Eibach installed

3rd Mod : Chasis stiffener - "Stiff Ring"

stiff ring washers

Front side washer (8 nos)

the washers are slotted in between the holding bolts and the gaps between the bolt hole and the chassis

View of the washer for the rear wheel (2 nos)

Please do not overtighten the washers

1. Immediate effect can be felt after installing these washers. the suspension felt more solid and comfortable over undulation.

2. this is because the chasis and the subframe has now become one unified body.

3. highly recommended for insight 2011.

4. these washers are replicas of a more expensive spoon rigid collars but works just about the same (at a fraction of the cost - USD 100 only).

2nd Mod : UltraRacing Front Strut Bar

New Upper Strut Bar

Being a hybrid car, fuel efficiency is the main idea. Stability, cornering and stuff, is thrown out of the window.

Well, the car isn't a performer when it comes to winding road, with tall centre of gravity, tayar sotong (squid tyre) with a width of only 185/55/16 (despite its 16inches rim, the rim width is so appalling), it doesn't even feel good to take a corner at a mere speed of 65km/h. Trust me, i have to lean myself to a side a bit if i am cornering.

The answer to all the predicament is a complete set of bracing bars at a predetermined spot. its like making the whole chassis frame more rigid to let it act as a unison body.

The first mod for this car in the handling department was this upper mount front strut bar. well, it isnt a strut bar because its not even bracing the strut mount itself but rather to the either side of the car body near the strut.

The feeling? an improvement during cornering. the car felt more stable when doing corners. on a plus note, the EPS of the steering felt more firmer than before.

However, please take note that this mod require a complete set of upper and lower mount bracing. with the absent of the lower brace, i can see that the car frame has "twisted" a bit with a gaping difference between the door panel and the fender panel.

1st Mod : K&N Air Filter

K&N Filter in place of the original filter

A sticker to warn of the "motorsport" element inside

The car was relatively new when i put K&N filter in, it only clocked 25,000 km to its record. I must say, everything was normal with the standard air filter. The filter is sufficient with normal style driving. 

However, on highway or at high speeds, the car lacks pushing power, especially when the IMA won't really be assisting at high rpms, the car felt like its "out of breath".

By putting the K&N filter in (part no. 33-2433), the engine behavior drastically changed :

1. Acceleration is more pronounce even from slower speeds. At middle to higher rpms, the car felt "eager" to move.

2. VTEC sounded more livelier this time. Passing 4,500rpm the car surges forward with a loud "praaaang" sound.

3. FC wise, not much different if the driving style is normal, however, with high speed pushings, the fc may drop to as low as 16km/l.

One of the benefits of K&N is that its washable. It's cotton media must be washed with a proprietor cleaner kit from K&N and its relatively easy to do.

Thanks to K&N, now i have committed a traffic offence.

It all began

The dyno blue pearl II color have been discontinued since the new FL introduction making it "rare'

in September 15, 2011 when i received the key to this hybrid car. Yes, its a Honda Insight 2011 model, a CBU unit imported from Japan.

What makes it interesting to own this car is that due to the fact that government of Malaysia is giving a hybrid incentive in a form of tax exemption for this car, meaning the price is right for a fully imported car.

This small car runs on a petrol-motor electric engine combination. its 1.3 engine is sufficient for 121Nm of torque and 88bhp, coupled with a motor providing 78 Nm of torque furthermore. In all its effort to cut down fuel consumption, cylinder deactivation is present in this car, autocruise,  brake regeneration and much more.

New engine look

Since its a hybrid providing at least 20km/l of fuel consumption, many would be owners felt that this car is underpowered. Rest assured that this hybrid can do much more (with a certain mod of course) whilst maintaining excellent fuel consumption.

This blog will document mods that have been carried out, reviews, tips and new projects.

All spanking clean and new and shouting "we want mod, we want mod"

With great powah, comes great kfc

Welcome to the blog mod of mine, some may call it rachuns, some may call it motorsports, whatever they're being called, this blog is about making an efficient hybrid engine more efficient.

Current mod